permanent mold casting

Permanent Mold Casting Technology to Improve Quality of Al-alloy Damping Cylinder

提高铝合金减震筒质量的金属型铸造工艺

Analysis for Defects of Water Faucet Handle by Permanent Mold Casting

金属型铸造水嘴手柄缺陷分析

Study on the Gating System of Permanent Mold Casting for Al Alloy

铝合金金属型铸造浇注系统设计研究

Process Optimization and Numerical Simulation for Shock Absorber Sleeve in Permanent Mold Casting

减震器筒体金属型铸造过程模拟及工艺优化

Permanent mold casting technology for large copper bush

大铜瓦的金属型铸造工艺

Permanent Mold Casting of Al-Si Alloy Body Case

Al-Si合金壳体的金属型铸造

Designing of Insulating Riser for Permanent Mold Casting by Modulus

模数法设计金属型铸造铝活塞保温冒口

Numerical Simulation of Filling and Solidification Process for Damper Cylinder of Motorcycle in Permanent Mold Casting

摩托车减震筒金属型铸造充型凝固过程数值模拟

Inlet Manifold for Ford Car in Permanent Mold Casting

福特电喷进气歧管金属型重力铸造工艺

Permanent Mold Casting for Slurry Pump Liner

泥浆泵缸套金属型铸造

Results prove that the water simulation test is economical and reliable in the research on molten metal permanent mold casting .

证明水力模拟研究熔融金属充填金属型的流动、消除充填造成的缺陷是可行的、经济的。

The performance , role , potential value and application ways of heat pipe in light alloy in permanent mold casting were expounded .

初步评估了热管在轻合金永久型铸造中的行为、作用、利用潜力和应用的基本形式。

Study on Semi-permanent Insulating Riser for Permanent Mold Casting of Al-piston

金属型铸造铝活塞半永久型保温冒口工艺研究

Research on the Multi-cycle and Multi-stage Simulation of High Pressure Die Casting , Low Pressure Die Casting and Permanent Mold Casting and Its Application

压力/低压/金属型铸造多周期、多阶段数值模拟技术的研究与应用

The cylinder and bands may be examined by a spectator before the drum is formed . Process Optimization and Numerical Simulation for Shock Absorber Sleeve in Permanent Mold Casting

在组装鼓之前圆筒和金属圈都可以被观众检查.减震器筒体金属型铸造过程模拟及工艺优化

Based on the permanent mold casting process of Al-piston , with top insulating riser feeding process , semi-permanent insulating sleeves matching permanent mold casting process of Al-piston have been designed .

根据金属型铸造铝活塞的工艺特点，采用顶部保温冒口补缩工艺，设计了能与铝活塞金属型铸造工艺相匹配的半永久型保温冒口套。

Technology Optimization and Quality Control of the Aluminium Inlet Manifolds in Permanent Mold Gravity Casting Process

金属型铸造汽车铝合金进气歧管的工艺优化与质量控制

The study was taken an oil sump as an example to analyze crack defect of permanent mold aluminum casting with thin thickness , deep cavity and large plane , and two causes , thermal stress and shrinkage stress during casting solidification .

以油底壳为例，分析了壁薄、深型腔、大平面铝合金金属型重力铸件，产生裂纹缺陷的原因，确定是合金凝固时期的热应力和收缩应力所致。

Study on Exhausting of Permanent Mold Cavity in Low-pressure Casting

金属型低压铸造型腔排气的研究

In this paper , the flow status and filling process of TiV15Cr3Sn3Al3 ( Ti 15 3 ) alloy melt in permanent mold during the centrifugal casting process have been analyzed and the laminar flow criterion , as well as the transforming rule of the sectional inclined angle are concluded .

本文分析了金属型离心浇铸TiV15Cr3Sn3Al3（Ti153）合金铸件的充型过程，得出了熔体在离心充型过程中的层流判据，以及熔体截面倾角的变化规律。